Cross-linked Triarylamine-Based Hole-Transporting Layer for Solution-Processed PEDOT:PSS-Free Inverted Perovskite Solar Cells.

The device performance of inverted organic metallohalide perovskite solar cells (OMPSCs) is optimized via tailoring the electrode surfaces with electron- and hole-transporting materials. This work demonstrates the fabrication of PEDOT:PSS-free OMPSCs using a hole-transporting composite material consisting of bilayered vanadium oxide (VO x) and a thermally cross-linked triarylamine-based material X-DVTPD, which contributes to higher Voc and Jsc values. The hydrophobicity of X-DVTPD resulted in the formation of large perovskite crystals and enhanced the stability of OMPSCs. Integration of ionic fullerene derivative, fulleropyrrolidinium iodide, in OMPSCs as a hole-blocking interfacial layer at the interface with Ag proves effective to further boost the device efficiency to 18.08%.

Bispentafluorophenyl-Containing Additive: Enhancing Efficiency and Morphological Stability of Polymer Solar Cells via Hand-Grabbing-Like Supramolecular Pentafluorophenyl-Fullerene Interactions.

A new class of additive materials bis(pentafluorophenyl) diesters (BFEs) where the two pentafluorophenyl (C6F5) moieties are attached at the both ends of a linear aliphatic chain with tunable tether lengths (BF5, BF7, and BF13) were designed and synthesized. In the presence of BF7 to restrict the migration of fullerene by hand-grabbing-like supramolecular interactions induced between the C6F5 groups and the surface of fullerene, the P3HT:PC61BM:BF7 device showed stable device characteristics after thermal heating at 150 °C for 25 h. The morphologies of the active layers were systematically investigated by optical microscopy, grazing-incidence small-angle X-ray scattering (GISAXS), and atomic force microscopy. The tether length between the two C6F5 groups plays a pivotal role in controlling the intermolecular attractions. BF13 with a long and flexible tether might form a BF13-fullerene sandwich complex that fails to prevent fullerene's movement and aggregation, while BF5 with too short tether length decreases the possibility of interactions between the C6F5 groups and the fullerenes. BF7 with the optimal tether length has the best ability to stabilize the morphology. In sharp contrast, the nonfluorinated BP7 analogue without C6F5-C60 physical interactions does not have the capability of morphological stabilization, unambiguously revealing the necessity of the C6F5 group. Most importantly, the function of BF7 can be also applied to the high-performance PffBT4BT-2OD:PC71BM system, which exhibited an original PCE of 8.80%. After thermal heating at 85 °C for 200 h, the efficiency of the PffBT4BT-2OD:PC71BM:BF7 device only decreased slightly to 7.73%, maintaining 88% of its original efficiency. To the best of our knowledge, this is the first time that the thermal-driven morphological evolution of the high-performance PffBT4BT-2OD polymer has been investigated, and its morphological stability in the inverted device can be successfully preserved by the incorporation of BF7. This research also demonstrates that BF7 is not only effective with PC61BM but also to PC71BM.

Reducing regioisomers of fullerene-bisadducts by tether-directed remote functionalization: investigation of electronically and sterically isomeric effects on bulk-heterojunction solar cells.

C60 bis-adduct containing a mixture of regio-isomers with different LUMO energy levels and steric geometries could greatly affect the morphological and bulk properties. To investigate the regio-isomer effect on solar cell performance, we have successfully designed and synthesized a regio-selective 4-acetatephenyl-4'-methylphenylmethano C60 bis-adduct (S-APM-CBA) by "tether-directed remote functionalization" strategy and a random 4-acetatephenyl-4'-methylphenylmethano C60 bis-adduct denoted as R-APM-CBA by traditional cyclopropanation. The dramatic reduction in the number of regio-isomers in S-APM-CBA is confirmed by the (1)H NMR and HPLC measurements and theoretical calculation. Compared to the R-APM-CBA-based device with a Jsc of 6.63 mA/cm(2), an FF of 44.3% and a PCE of 2.46%, the device using S-APM-CBA yielded a much lower Jsc of 1.48 mA/cm(2), an FF of 32.2%, and a PCE of 0.38%. Consistently, the electron-only device using S-AMP-CBA exhibited lower electron mobility than the R-AMP-CBA-based device. These results imply that the electronic shallow-trap effect ascribed to the LUMO energy variations turned out to be insignificant in the AMP-CBA system. The lower efficiency and mobility of S-AMP-CBA might due to the assumption that the most probable trans-4-III isomer in S-AMP-CBA prevents the intermolecular facial contact of fullerenes, thereby hindering the electron transporting. Furthermore, the nanomorphology of S-AMP-CBA and R-AMP-CBA active layers could be different because of their different three-dimensional structures. This research demonstrated that steric effect of regio-isomers in a given C60 bis-adduct is more crucial than electronic shallow-trap effect.

A new ladder-type benzodi(cyclopentadithiophene)-based donor-acceptor polymer and a modified hole-collecting PEDOT:PSS layer to achieve tandem solar cells with an open-circuit voltage of 1.62 V.

We have developed a new ladder-type conjugated polymer and a robust interconnecting layer (ICL) integrating a hole-collecting m-PEDOT:PSS layer with an electron-collecting ZnO layer. The inverted device using exhibited a high power conversion efficiency (PCE) of 5.76% with a Voc of 0.81 V, a Jsc of 12.82 mA cm(-2), and a FF of 55.5%. The inverted tandem device incorporating the and ICL achieves a Voc of 1.62 V leading to a PCE of 7.08%.

Interface engineering to enhance the efficiency of conventional polymer solar cells by alcohol-/water-soluble C60 materials doped with alkali carbonates.

Two new C60-based n-type materials, EGMC-OH and EGMC-COOH, functionalized with hydrophilic triethylene glycol groups (TEGs), have been synthesized and employed in conventional polymer solar cells. With the assistance of the TEG-based surfactant, EGMC-OH and EGMC-COOH can be dissolved in highly polar solvents to implement the polar/nonpolar orthogonal solvent strategy, forming an electron modification layer (EML) without eroding the underlying active layer. Multilayer conventional solar cells on the basis of ITO/PEDOT:PSS/P3HT:PC61BM/EML/Ca/Al configuration with the insertion of the EGMC-OH and EGMC-COOH EML between the active layer and the electrode have thus been successfully realized by cost-effective solution processing techniques. Moreover, the electron conductivity of the EML can be improved by incorporating alkali carbonates into the EGMC-COOH EML. Compared to the pristine device with a PCE of 3.61%, the devices modified by the Li2CO3-doped EGMC-COOH EML achieved a highest PCE of 4.29%. Furthermore, we demonstrated that the formation of the EGMC-COOH EML can be utilized as a general approach in the fabrication of highly efficient multilayer conventional devices. With the incorporation of the EGMC-COOH doped with 40 wt % Li2CO3, the PCDCTBT-C8:PC71BM-based device exhibited a superior PCE of 4.51%, which outperformed the corresponding nonmodified device with a PCE of 3.63%.